What This Cut List Calculator Does
You enter the sheet size, the saw kerf and each part with its width, length and quantity. The cut list optimizer (a cutlist optimiser, in British spelling) places every part on the sheets, leaves room for each saw cut and tells you how many sheets you need and how much of each one you use.
Set up the sheet
Width and length in mm or inches (mm | in switch), kerf, an optional trim margin and, if the board has a grain, the grain option.
Add the parts
Type them in or paste a CSV list: name, width, length, quantity.
Calculate and export
Check the sheet count and the yield of each sheet, then export the plan as a PDF or save the project.
Worked Example: Two Bookcases
Two identical open bookcases in 3/4 in (18 mm) plywood: two sides, a top, a bottom, four shelves and a toe kick each — 18 parts in total. We ran the same project twice in the optimizer, once on a 4×8 ft sheet with inch sizes and once on a 2440 × 1220 mm sheet with metric sizes. Grain direction off, no trim margin. The numbers below are the optimizer's own results, not estimates. For a plywood-only job with grain locked on the sides and doors, see our plywood cut list optimizer example.
US & Canada: 4×8 ft sheet, sizes in inches
Bookcase 84 in tall, 36 in wide, 12 in deep. Entered in inches with the mm | in switch set to in: the 4×8 ft sheet preset (48 × 96 in), kerf 1/8 in and part sizes typed as fractions such as 11 1/4. The optimizer converts every size exactly (1 in = 25.4 mm) and calculates in millimeters internally; the last column shows those values.
| Part | Size (in) | Used internally (mm) | Qty |
|---|---|---|---|
| Side | 11 1/4 × 84 | 285.75 × 2133.6 | 4 |
| Top / bottom | 34 1/2 × 11 1/4 | 876.3 × 285.75 | 4 |
| Shelf | 34 1/2 × 11 | 876.3 × 279.4 | 8 |
| Toe kick | 34 1/2 × 3 1/2 | 876.3 × 88.9 | 2 |
Sheet 1 holds the four sides (82.0% used). Sheet 2 holds the four tops and bottoms, six shelves and one toe kick (85.7%). Sheet 3 holds the last two shelves and the second toe kick (19.1%). Parts area: 59.79 sq ft (5.55 m²); offcuts and saw kerf: 36.21 sq ft (3.36 m²).
UK, Ireland, Australia & New Zealand: 2440 × 1220 mm sheet
Bookcase 2100 mm tall, 900 mm wide, 300 mm deep. Kerf 4 mm, the optimizer's default.
| Part | Size (mm) | Qty |
|---|---|---|
| Side | 300 × 2100 | 4 |
| Top / bottom | 864 × 300 | 4 |
| Shelf | 864 × 280 | 8 |
| Plinth | 864 × 80 | 2 |
Sheet 1 holds the four sides (84.7% used). Sheet 2 holds the four tops and bottoms, six shelves and one plinth (85.9%). Sheet 3 holds the last two shelves and the second plinth (18.6%). Parts area: 5.63 m²; offcuts and saw kerf: 3.30 m². For sheets, yield and calculation time in three runs, see our 15-part cabinet benchmark.
Standard Sheet Sizes by Market
| Market | Common sheet | Enter in the optimizer |
|---|---|---|
| US & Canada | 4 × 8 ft (48 × 96 in) | 1219 × 2438 mm |
| UK & Ireland | 8 × 4 ft (2440 × 1220 mm) | 2440 × 1220 mm |
| UK & Ireland, large format | 2800 × 2070 mm (melamine, chipboard) | 2800 × 2070 mm |
| Australia & New Zealand | 2400 × 1200 mm | 2400 × 1200 mm |
| Australia, extended | 3600 × 1200 mm | 3600 × 1200 mm |
For a full example on the large format, see our melamine and MDF cut list on 2800 × 2070 mm boards, with plain white and woodgrain boards compared.
Always check the exact size your supplier stocks: a few millimeters of difference can change the whole layout.
Why This One
Kerf, grain, rotation and PDF plans are what you would expect from any cut list optimizer. These are the parts of optimizadordecorte.app that go further:
Parts from a photo
In Auto Cutlist, upload a photo, a dimensioned drawing or a 3D render of a piece of furniture. The detected parts are shown for you to review before they are added; sizes read from dimension lines are marked as confirmed, and those judged by eye as estimated.
3D furniture configurator
Design wardrobes, cabinets and shelving in the 3D configurator and get the full parts list in one click, ready to send to the optimizer. To see a four-unit kitchen taken from parts list to cutting plan, read our kitchen cabinet cut list example.
DXF export for CNC
From the 3D configurator, export dimensioned front, side and top views as DXF files, with separate layers for outlines, hinge holes and drawer slides.
QR labels for every part
The label generator prints a label for each part with its size and a QR code with its production route, so parts stay identified after they leave the saw.
The free plan includes a set number of calculations per day; Premium makes them unlimited.
Try it with your own parts
Enter your sheet size and parts list and get the cutting plan in seconds.
▶ Open the cut list optimizerFAQ
What kerf should I enter?
Enter the width of your saw blade, in millimeters or inches; in inches the default is 1/8 in. A standard full-kerf table saw or panel saw blade is about 1/8 in (3.2 mm); a thin-kerf blade is about 3/32 in (2.4 mm). The optimizer leaves that gap between neighboring parts, so the cut parts come out at full size. If in doubt, measure a test cut.
Can I keep the grain direction on some parts?
Yes. Turn on "Board with grain/fiber" and tick the grain box on the parts that must follow it, such as doors and visible end panels. Those parts are never rotated; the rest can be turned 90° to fit better.
What sheet sizes can I use?
Any size, in millimeters or inches: 2440 × 1220 mm in the UK and Ireland, 2400 × 1200 mm in Australia and New Zealand, or 48 × 96 in for a 4×8 ft sheet in the US and Canada. In inches, one-click presets fill in 4×8, 4×4 and 5×5 ft sheets. You can also add a trim margin around the edge.
How much material does a cutlist optimiser save?
It depends on the parts. In the worked example on this page, 18 parts fit on 3 sheets: the first two sheets are more than 80% used, and the third holds only 3 parts, leaving a large offcut you can keep for the next job. The optimizer shows the yield of every sheet, so you can see exactly where the waste is.
Does it work in inches or millimeters?
Both. It works in millimeters by default; switch the mm | in toggle next to Board configuration to type sizes in inches, with decimals or fractions such as 11 1/4, 3/4 or 4 ft. Results, areas (in sq ft) and the PDF are then shown in inches, rounded to the nearest 1/16 in. Internally the optimizer always calculates in millimeters, using the exact conversion (1 in = 25.4 mm), and saved projects are stored in millimeters.
Is a cut list calculator the same as a cut list optimizer?
Yes, people use both names for the same tool. A calculator in this sense does more than add up areas: it places every part on the sheets and tells you how many sheets you need, allowing for the saw kerf.
Is a cutting plan generator something different?
No. Cutting plan generator, cut list generator and panel cutting calculator are other names for the same job: the result is a cutting plan for each sheet that you can take to the saw.