MDF vs Plywood: Cutting, Grain & Sheet Sizes

MDF and plywood go through the same cut list optimizer (or cutlist optimiser) in the same way, with one difference: grain. Below, one cabinet is planned as plywood and as MDF on three sheet sizes, with the real results.

▶ Open the optimizer

By The optimizadordecorte.app Team · Last updated:

The difference that matters for planning: grain

Plywood has a face veneer with a visible grain, so doors and visible sides usually need it to run one way. Plain MDF has no grain, so every part can be turned. In our optimizer you switch on Board with grain/fiber and lock the parts that need it for plywood, and leave grain off for plain MDF.

The test cabinet

PartWidth × height (mm)Width × height (in)QtyGrain locked (plywood)
Side560 × 72022 1/16 × 28 3/82Yes
Top764 × 56030 1/16 × 22 1/161No
Bottom764 × 56030 1/16 × 22 1/161No
Shelf762 × 54030 × 21 1/42No
Door397 × 71615 5/8 × 28 3/162Yes
Back764 × 68430 1/16 × 26 15/161No
Plinth764 × 10030 1/16 × 3 15/162No

To get a cabinet’s parts without working them out by hand, use the cabinet cut list generator.

Results

MaterialSheet (as entered)Kerf · marginSheetsAverage yield
Plywood, grain on sides and doors48 × 96 in1/8 in · none262.7%
MDF, no grain48 × 96 in1/8 in · none262.7%
Plywood, grain on sides and doors1220 × 2440 mm4 mm · none262.6%
MDF, no grain1220 × 2440 mm4 mm · none262.6%
Plywood, sheet entered as 2440 × 1220 mm2440 × 1220 mm4 mm · none341.8%
MDF, no grain2800 × 2070 mm4 mm · 10 mm164.3%

Grain cost nothing for this cabinet when the sheet was entered with its height along the grain, in inches or millimeters. Entering the sheet the other way round put the grain across the sheet, so the locked sides and doors could not lie along it, and the plan needed a third sheet at 41.8% yield. In our optimizer a grain-locked part keeps its height along the sheet’s height, so enter the sheet with its grain direction as the height.

Sheet sizes

The optimizer accepts any sheet size, so use the sizes your supplier actually stocks. With plain MDF on a 2800 × 2070 mm board and a 10 mm trim margin, the same cabinet fits on one board. A larger board is not always better: run your list on each size you can buy and compare the sheets and the wasted area, which every result shows.

Cutting settings for both

Kerf: enter the width of your blade; the optimizer leaves that gap between parts. Trim margin: taken off every edge of the sheet, for edges that are damaged or not square. Edge banding: not handled by the optimizer; the 3D configurator records it in its PDF and DXF files.

Try it with your own parts

Enter your sheet size and parts in millimeters or inches and get the cutting plan in seconds. No sign-up needed to start.

▶ Open the optimizer

FAQ

Should I lock grain for MDF?

Not for plain MDF, which has no grain. Leave grain off so the optimizer can rotate parts. Lock it for plywood parts whose face shows.

Is a cutlist optimiser different for MDF and plywood?

No. It is the same optimizer; only the grain settings change.

How should I enter a plywood sheet?

With the grain direction as the height, for example 48 × 96 in or 1220 × 2440 mm, so grain-locked parts can run along it.

Written by the team behind optimizadordecorte.app — learn more about how the tool works.